How To Fix LED Light Strip? – Using LED Light strips you can design your home in a better way. These types of lights are quite easy-to-use strips, and flexible. Also, they can be cut down to specific lengths as per the need of the individual. So here are some of the simple steps to know How To Fix LED Light Strip?
LED Lights Won’t Turn On
Well, the first step to troubleshoot and fix the LED light strip is to work out from the bottom (power source) up to the end of the light strip.
So that you can find the potential issues and troubleshoot whether the problem is in the power source, controller, connection, and so on.
- Check out the power source of your lights.
- Find whether the power supply is overloaded or not
- .Also check the on/off switch or controller.
- If you have got battery operated light, make sure to add new batteries.
- Test each connection point for loose or incorrect polarity.
- Last but not least, find the bending sections of the light strip.
How To Fix LED Light Strip?
A LED light strip is quite difficult to damage, however, if put under enough stress it can tear out. Another major cause may be bending light strips around corners without proper connections.
Some of the things that you can do to fix the LED Light strip:
- Find out the area of damage.
- Then unplug the light strip.
- Detach the adhered lights.
- To cut the damaged section use scissors to cut along the copper marking.
- Then cut a new section of the same strip light.
- Now time to attach pin connectors to each and every section of the light strip.
- Make sure to use connector pins of 2 pins, 4 pins, or 5 pins.
- Last test your lights and re-adhere to the surface.
How To Cut LED Light Strips?
If any section of the LED light strip has got damaged diodes then you can easily cut out the damaged section and replace it with the same model strip lights.
You might question where to cut. You can cut on the copper markings. These copper markings are usually 1 or 2 inches throughout the light strip roll. Make sure t leave a bit of copper as you need to connect it with the new section of light.
Now it’s time to use connector pins which allow you to connect two sections of strip lights. Pin connectors easily allow current to pass through the damaged area without any interference.
The Power Source
The power source could be one of the problems if your light is not working completely. First of all, check whether the switch of the particular outlet is turned on or not.
Besides these, any type of modification or attachment of additional light strip rolls can overload the power supply or plug in the adapter. So it is always better to have a max power supply limit before adding additional light strips. As per our research, most plug-in style power supplies can handle 24 watts to 60 watts of LED Lights,
Note: Check out the manufactures specification for more information.
Light Strip Voltage
Make sure to use proper voltage, if you are just installing and lights are not working. Mixing several voltages may result in light o not working correctly. Some of the common brands used are 12V, 24V, or 120 V setups. In some cases, a plug-in adapter converts 120V to 12V or 34V to work with low voltage LED Lighting. So keep in mind that you should use the same one throughout the project
Troubleshooting Connections
Most of the time a loose connection may cause an LED light strip not to turn on. So go through the entire section of the light strip and test for any loose junction points. Many people overlook these during an installation, so double-check for potential errors.
Light Strip Copper Sections
If the light strip junctions do not make a proper connection to the copper designations problem may arise. So be very careful while cutting out the light strip with the scissor. As these lights have got relatively weak connections so any trouble in copper may result in potential lighting issues.
Besides these factors, the adhesive backing film may interfere with connections. So check on whether the backing film is properly cut.
Using Correct Polarity
If you have 90-degree turns or wired jumper connections, you might be willing to check the polarity of the connection points which may cause issues. Make sure that positive marking (+) is going to the positive (+) and negative marking(-) to negative (-). If the polarity is flipped then the light won’t work. So the fix this issue simply flip the polarity of the connection and test whether your lights work or not
The Controller Or Remote
Besides the connection points, controllers can also cause light to not work properly. So here are a few things you need to consider:
- If using a remote, first check if you have changed out the battery or not.
- Check and test the polarity connections.
- Last but not least, make sure you have got a strong connection point from the power source to your light strips.
Radio Frequency Interference
Always double-check that the dimmer box was not installed near any motorized things. This may cause radio frequency interference with the remote.
Time To Conclude – How To Fix LED Light Strip?
Here we have presented all possible methods regarding How To Fix LED Light Strip? If your light strips are beyond repair then go with the new light strip. As of now, we do have lots of options with LED light strips. You can go with Govee-LED Light Strips with remote control.
Have A Good Day Cheers!!!
You May Also Like: